Esp guitar dating Sex web chats in zambia
The 2nd one I bought [...] was totally moded for guitar with extra pots on the back and stock EL34s. I [...] have [an YBA-1A Mark II amp] that goes with [the YT-15 cabinet] and it's all sounds great. i believe, though i am not sure, that these 1a's operate in class "a". Other than the old no ground power cord and serious shocks and buzz it sounded better than what i was using.i stuck a master volume on the back, jumped the channels, and cranked both channels to 7-8, plugged in my custom shop '61 reissue sg, and it kicks so much ass [through 4x12 25w greenbacks] its indescribable i bought both a 1971 yba-1 and a 1972(? [...] the yba-1a is currently beating the snot out of an old mesa 4x12 with 90 watters in it. this would make sense to me considering how very crushing it is and yet chimey. The only real problem was it seemed to be blowing fuses.I've used it regularily throughout the years, gigging throughout the Detroit area, and later in the E. A plate load of 6K8 would have essentially zero gain and probably lots of other problems.That part of the hand-drawn schematic from 6/1971-1974 is smudged and hard to read, but it's definitely 68K.] 0 [used], very early model, the serial number is 0278, which places it in 1966, uses 6CA7 tubes as specified in the tube chart, no tube rectifier, and the marshall style phenolic turret board, also, it has the hole in the chassis for the tube rectifier socket, but it is blocked with a circular steel plate, the 5 volt rectifier heater winding at the power tranny is cut about 2 inches out, December 1998 Rating Very good one. I have a 1977 YBA1 with a matching YT-15 cabinet [...]. It's probably not worth a tird as a collector's item but this amp really screams. I rate my YRM-1 second to my YBA-1, because it does not have as much balls.This must have been one of the last real Traynor amps made... Also, my YBA-1 sounds great at all volumes, including low setttings. 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), logo 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), front view, angle 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), front view 1965 or 1966 YBA-1 Bass-Master (old wrap-around style case), back view 1966 YBA-1 Bass-Master, chassis 1966 YBA-1 Bass-Master, wiring 1968 YBA-1 Bass-Master (serial number 2xxx), front view, angle 1968 YBA-1 Bass-Master (serial number 2xxx), front view 1968 YBA-1 Bass-Master (serial number 2xxx), logo YBA-1 Bass-Master, catalog page YBA-1 Bass-Master, catalog page YBA-1 Bass-Master, schematic 10/1966 YBA-1 Bass-Master, schematic 6/1971-1974 YBA-1 Bass-Master, schematic 5/1974 - Please note: This schematic has a serious error in it.
Better sound as a Fender Bassman; lower powered, would work just fine in a blues or lower volume setting (when used for bass or guitar). ] 0 [used], a 1978 YBA-1 together with a 1977 YT-15, both mint [US?Features silvery grey grille cloth Yorkville [...] owns Dyna-Bass #0011 and [has] used it as a promotional tool.Sound - Reliability - Price CAD 5 [used], condition unknown, Scarborough, Ontario, Canada, February 7, 2001 Very hard to find. Dyna-Bass, front view, angle (apparently the same as the following) 1963 Dyna-Bass, serial number 0011, front view, angle Features Two channels, deep (bass), and bright (guitar); each has an attenuated and a normal gain input (like the old Marshalls); no reverb Volume control channel one, channel two; treble, bass, low range expander, high range expander (passive); the low range expander may sound like a mid-range, the hi range expander may sound like presence (on Marshalls or Fenders) to some (the section is a virtual clone of that of the Marshall JTM-45); standby switch; pilot light; ground and on/off switch; no fan One main speaker output, impedance is not indicated (runs fine using a cab of eight ohms, also often operated with four ohm loads), one "extension" speaker output also without indicated impedance.A 1967 YBA-1 is reported to feature a diode rectifier.The used tubes are, as indicated in the amp: Two 6CA7s (replaceable by EL34s) and three 12AX7As (also called 7025s or ECC83s); plate voltages have always been a question on these units, but I think this may be largely because of confusion with the YBA-1A models that run VERY high plate voltages; most of the YBA-1 models probably come in somewhere /-450 volts (one has reported 425 volts on plate, another one ca.
More power and punch than Fender, less ruggedness than Marshall.